dfw

blownaltered · 10-14-2013, 08:29 AM

In the old fox body I've been looking at kmembers with some front coil overs. I'm going to out different rear gears in it as well sometime soon.

**JDBishopArts** · 10-14-2013, 09:42 AM

ID1000s, BAP, Vorshlag CC plates, UCA, One piece DS, DS loop, CF hood vents. Not sure what order that is going to be in.

**Dan12GT** · 10-14-2013, 10:47 AM

Originally Posted by BERT

Why not Tokico D-Specs?

I've considered those as well however they cost the same as Koni so it would be a wash as far as cost is considered. I am more familiar with Koni as far as the brand goes.

**cmanley99** · 10-14-2013, 12:28 PM

wider wheels and tires for sure...then a uca/lca's. Those 3.73's rock with the auto but need the tires for sure.

ProCharge5.0 · 10-19-2013, 06:32 PM

Originally Posted by Kaane

Driver Side for sure, So I am guessing 8.

I will pull the plugs soon and take a look.

Funny thing other than smoke, You can't really tell. It still drives normal, no sounds of any kind and no check engine light. It dumped half a quart of oil through the breather though.

Same thing mine did. Mine doesn't even smoke. Just a ton of crankcase pressure. Compression is down on 3 cyl. I was looking at the MMR 1000 build as well but I am nervous about using them.

blownaltered · 10-19-2013, 10:31 PM

Originally Posted by ProCharge5.0

Same thing mine did. Mine doesn't even smoke. Just a ton of crankcase pressure. Compression is down on 3 cyl. I was looking at the MMR 1000 build as well but I am nervous about using them.

If you call on the corral.net there are a bunch of guys that tell horror stories about them.

**south.texas.dead.I** · 10-21-2013, 12:14 AM

Just ordered a diablosport intune from AM

**OG Fox** · 10-21-2013, 12:19 AM

Originally Posted by south.texas.dead.I

Just ordered a diablosport intune from AM

yikes....why

**garner** · 10-21-2013, 12:22 AM

Well my next mods are set of 19" staggered am rtr wheels and lethal offroad h pipe

**DirtyD** · 10-21-2013, 10:13 AM

Originally Posted by south.texas.dead.I

Just ordered a diablosport intune from AM

You better get a custom tune for it from someone other than Bama....

**Yagermeister** · 10-21-2013, 10:16 AM

Originally Posted by south.texas.dead.I

Just ordered a diablosport intune from AM

Originally Posted by DirtyD

You better get a custom tune for it from someone other than Bama....

JPC Racing does a good job with the Diablosport stuff. Call and talk to Justin and tell him Brent Yager sent you

**mavfan37** · 10-22-2013, 01:21 AM

Some kind of FI. I have been trying to decide on building the block first or just going FI. But today I decided after taxes that I will be going for FI. Now I just need to decide on what type.

**maxpayne** · 10-22-2013, 10:17 AM

Originally Posted by maxpayne

Ordering a set of 18" by 10" sve drifts with nitto tires tomorrow. Springs, panhard, struts/shocks, and miscellaneous is next at Christmas for a 1" or 1.5" drop - haven't decided yet.

Y'all think 10" wide wheels on the front will stick out bad, or if at all?

Ended up getting a set of brand new '14 California Special wheels/tires. They look great! - even though they aren't very performance oriented.

**46Tbird** · 10-22-2013, 10:59 AM

I've got a used pair of FRPP / Boss 302S lower control arm relocation brackets and a new pair of CHE LCAs to put on this week. I'll see if I can get it to hook any harder with a fresh pair of 20" DRs and shoot for an untuned 11.x pass. I doubt it will happen but we'll see, lol.

**wbt** · 10-22-2013, 11:57 AM

Originally Posted by 46Tbird

I've got a used pair of FRPP / Boss 302S lower control arm relocation brackets and a new pair of CHE LCAs to put on this week. I'll see if I can get it to hook any harder with a fresh pair of 20" DRs and shoot for an untuned 11.x pass. I doubt it will happen but we'll see, lol.

With good weather and a hook I think it is possible and would be a great achievement IMO.