That is what it's all about, enjoying what you like to do. I didn't get a chance to see your car run but heard good things about it.
On the manual trans stuff, I just hate to see stuff break when it doesn't have to. It is relatively expensive to get the driveline up to snuff but makes for a safer, more reliable car. It also gives you room to grow with power.
Most build their cars from front back vs. back to front and hopefully with some shared experience everyone can enjoy their cars how they were meant to be.
This clip shows my driver side axle breaking on launch using a full slick:
The ET streets are the DOT slick, right? I've always heard that manuals need to go with something other than DRs, because they are too stiff to take the drivetrain shock.
The ET streets are the DOT slick, right? I've always heard that manuals need to go with something other than DRs, because they are too stiff to take the drivetrain shock.
A slick when wrinkle and collapse a bit, it absorbs the shock and will help preserve driveline parts with an aggressive manual trans launch. In my experience anyway.
__________________
My daily is faster then your race car
The ET streets are the DOT slick, right? I've always heard that manuals need to go with something other than DRs, because they are too stiff to take the drivetrain shock.
Originally Posted by Junkie
A slick when wrinkle and collapse a bit, it absorbs the shock and will help preserve driveline parts with an aggressive manual trans launch. In my experience anyway.
This was the first time at the track with a full Hoosier bias ply slick slick on the car. 28x10x15. When I launched it hit the tires, they stuck, and the axle said, "I am getting a beer, this is BS.". First run of the night, first hit, then back on the trailer. :P
Prior to this I was using ET Street bias ply tires on 8" rims.
This was the first time at the track with a full Hoosier bias ply slick slick on the car. 28x10x15. When I launched it hit the tires, they stuck, and the axle said, "I am getting a beer, this is BS.". First run of the night, first hit, then back on the trailer. :P
Prior to this I was using ET Street bias ply tires on 8" rims.
So the ET streets are a good tire for someone like myself to get for track use on a manual?
So the ET streets are a good tire for someone like myself to get for track use on a manual?
Quick Time Pro. BAD ass tires, I hooked on the street and track with them with a stick and over 700 rw. lasted about 5-6k miles too which is better than a drag radial. They are DOT legal for street use, even though Hoosier says not to use them on the highway.
So the ET streets are a good tire for someone like myself to get for track use on a manual?
Originally Posted by STROKD
Quick Time Pro. BAD ass tires, I hooked on the street and track with them with a stick and over 700 rw. lasted about 5-6k miles too which is better than a drag radial. They are DOT legal for street use, even though Hoosier says not to use them on the highway.
Sure. Either one of those tires would be fine for a manual trans car.
Run a 10" wide rim with a 28x11.50-15 sized tire. I would start at 14psi. on the track and go from there.
If you drive with them on the street I would run about 25psi. If it rains do not drive on them.
BTW - I used to be a MT guy for years. IMO I think Hoosier makes a better tire today.
Sure. Either one of those tires would be fine for a manual trans car.
Run a 10" wide rim with a 28x11.50-15 sized tire. I would start at 14psi. on the track and go from there.
If you drive with them on the street I would run about 25psi. If it rains do not drive on them.
BTW - I used to be a MT guy for years. IMO I think Hoosier makes a better tire today.
yep, i ran a 15x10 with a 28x11.50... fit perfect, very little walk at speed, had them over 180 on the highway a few times... I ran 20-22 on the street (18 when I was racing) and 12-15 at the track depending on the heat in the track and prep. Never had to go below 12 hot, it would start biting REAL well at 12 if it needed to go that low.
A slick when wrinkle and collapse a bit, it absorbs the shock and will help preserve driveline parts with an aggressive manual trans launch. In my experience anyway.
I ran 20-22 on the street (18 when I was racing) and 12-15 at the track depending on the heat in the track and prep. Never had to go below 12 hot, it would start biting REAL well at 12 if it needed to go that low.
Hybrid Mode
