Dallas Fort Worth 5.0 Mustang Club
Page 2 of 3 1 2 3
Show 40 post(s) from this thread on one page

Dallas Fort Worth 5.0 Mustang Club (http://www.dfw50s.com/index.php)
-   Member's Rides (http://www.dfw50s.com/forumdisplay.php?f=29)
-   -   Re-Rx7's Sterling Grey 11' (http://www.dfw50s.com/showthread.php?t=3332)

JDMLOL 12-30-2013 08:43 PM
It was a pita for me. Ripped some paint off of my trunk too :/ No spoiler ftw.

re-rx7 12-30-2013 09:53 PM
Tell me about it. Thanks Alex.

Midnight11 12-30-2013 09:56 PM
Yup lol not bad if you have a heat gun

Dominic Toretto 12-30-2013 10:04 PM
Quote:
Originally Posted by JDMLOL (Post 59834)
It was a pita for me. Ripped some paint off of my trunk too :/ No spoiler ftw.
You did it wrong then.

Quote:
Originally Posted by Midnight11 (Post 59840)
Yup lol not bad if you have a heat gun
I just used plenty of Goo Gone.

-Alex

downtime! 12-30-2013 10:41 PM
A little Goo Gone, a little heat gun and a little 50 pound test braided fishing line (with 2 sticks on the ends, used like a saw) and they come off quite easy. Also helps to do it on a hot Texas summer day.

re-rx7 12-31-2013 12:16 AM
I did it in the 29 degree wind blowin out of the north at 30mph weather. Like a boss.

Dominic Toretto 12-31-2013 12:24 AM
Quote:
Originally Posted by re-rx7 (Post 59855)
I did it in the 29 degree wind blowin out if the north weather at 30mph weather. Like a boss.
Did you use double-sided tape on the new spoiler?

-Alex

re-rx7 12-31-2013 12:52 AM
Quote:
Originally Posted by Dominic Toretto (Post 59857)
Did you use double-sided tape on the new spoiler?

-Alex
Yes, 3m. Followed the same outline that it came off with.

Dominic Toretto 12-31-2013 08:50 AM
Quote:
Originally Posted by re-rx7 (Post 59860)
Yes, 3m. Followed the same outline that it came off with.
Might want to go over it with a hair dryer at some point. I can't be sure but, I was told that the tape needs to be warm to properly adhere. I have not tried to prove this on my car by removing the screws and pulling on it.

-Alex

re-rx7 12-31-2013 11:25 AM
Quote:
Originally Posted by Dominic Toretto (Post 59873)
Might want to go over it with a hair dryer at some point. I can't be sure but, I was told that the tape needs to be warm to properly adhere. I have not tried to prove this on my car by removing the screws and pulling on it.

-Alex
I believe pressure is a more important factor then temp. I usually put C clamps on them for an hr so before removing.

pohnjarker 12-31-2013 01:13 PM
Quote:
Originally Posted by my95z28 (Post 59412)
Looks good man! Any close up pics of how the 305/35-20s fit? Looking at putting some Nittos on a 10" wheel, trying to decide whether to go 305 or 315 since they run so narrow.
I have 315 NT05 on a 20x10 and they fit well. i've had no issues with them.

03MachMe 12-31-2013 08:08 PM
Pic please?^^

re-rx7 01-02-2014 12:51 AM
Clean shot after wash.
http://i44.photobucket.com/albums/f3...psqmimsb1n.jpg

re-rx7 02-26-2014 04:47 PM
Lowered on FRPP K springs, GT/CS facia added oh and gt500 mudflaps!! Whoo! Car is coming along nicely.

http://i44.photobucket.com/albums/f3...psofojdkz7.jpg

http://i44.photobucket.com/albums/f3...psrq6qampa.jpg

http://i44.photobucket.com/albums/f3...ps6xwewkio.jpg

Dominic Toretto 02-26-2014 04:51 PM
Looks good man. You plan on keeping the factory grill?

-Alex


All times are GMT -4. The time now is 06:10 PM.
Page 2 of 3 1 2 3
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.