Performance Post anything performance related to your Mustang |
Sponsored Ads |
|
Welcome to DFW50s.com
|
Register to remove these ads.
10-10-2012, 11:10 PM
|
#1
|
I> /\/\
Join Date: Jun 2012
Location: A fender ahead of BlownAltered
Posts: 7,562
|
Originally Posted by TrueStreetTim
To a degree.....yes. If there is anything in common, maintenance wise, is I get calls about O2 codes. Typically with replaced headers, yes. But also those without. But keep in mind, no cats will kill them especially fast by comparison.
If you decide to change your sensors out, make sure they are OEM straight from Ford (not Bosh etc.) Tuning has shown us that the aftermarket sensors heat up and cool down just differently enough than OEM to possibly throw codes.
|
Knowing it would leave some HP on the table, but do the stock cats overheat if the stock midpipe is left in place?
|
|
|
10-11-2012, 11:15 AM
|
#2
|
DFW5.0s Preferred Vendor
Join Date: Aug 2012
Location: McKinney
Posts: 676
|
Originally Posted by Steve
Knowing it would leave some HP on the table, but do the stock cats overheat if the stock midpipe is left in place?
|
I like where your going with this.
Not so much the heat as it would also be the added pressure from a higher flowing header. Especially if the car is S/C'd....you'll blow it apart! And without a tune after your header swap, you'll 100% throw codes. The midpiping must be replaced, along with the cats (or none), with a header swap!
ARH is already manufacturing a shorty header for the new Camaro and promise to have the Mustang shorty available early next year. The design meets EPA and will not require a midpipe setup (or tune i believe) to bolt to the factory system. A cheaper option for folks. But if you get anything other..... don't try to use the factory piping & cat's.
Last edited by TrueStreetTim; 10-11-2012 at 11:22 AM.
|
|
|
10-11-2012, 12:54 PM
|
#3
|
I> /\/\
Join Date: Jun 2012
Location: A fender ahead of BlownAltered
Posts: 7,562
|
Originally Posted by TrueStreetTim
I like where your going with this.
Not so much the heat as it would also be the added pressure from a higher flowing header. Especially if the car is S/C'd....you'll blow it apart! And without a tune after your header swap, you'll 100% throw codes. The midpiping must be replaced, along with the cats (or none), with a header swap!
|
What about with the stock headers? Will the stock midpipe live a long happy life with a power adder? I'm asking, because I don't want this car to be obnoxiously loud. My little girl rides in this car often and I rather not she be deaf by the time she is five. lol
Last edited by Grandpa; 10-11-2012 at 01:05 PM.
|
|
|
10-10-2012, 08:57 PM
|
#4
|
I> /\/\
Join Date: Jun 2012
Location: A fender ahead of BlownAltered
Posts: 7,562
|
Are you guys seeing any issues with the 02's with the longtubes on these Coyote motors?
|
|
|
10-10-2012, 10:50 PM
|
#5
|
DFW5.0s Preferred Vendor
Join Date: Aug 2012
Location: McKinney
Posts: 676
|
Originally Posted by Steve
Are you guys seeing any issues with the 02's with the longtubes on these Coyote motors?
|
To a degree.....yes. If there is anything in common, maintenance wise, is I get calls about O2 codes. Typically with replaced headers, yes. But also those without. But keep in mind, no cats will kill them especially fast by comparison.
If you decide to change your sensors out, make sure they are OEM straight from Ford (not Bosh etc.) Tuning has shown us that the aftermarket sensors heat up and cool down just differently enough than OEM to possibly throw codes.
Last edited by TrueStreetTim; 10-10-2012 at 10:59 PM.
|
|
|
10-11-2012, 11:09 AM
|
#6
|
Senior Member
Join Date: Aug 2012
Location: Keller, TX
Posts: 613
|
Originally Posted by Steve
Are you guys seeing any issues with the 02's with the longtubes on these Coyote motors?
|
Funny you ask, http://dfw50s.com/showthread.php?t=454
been a nightmare and $300 to get this mess fixed.
Originally Posted by TrueStreetTim
To a degree.....yes. If there is anything in common, maintenance wise, is I get calls about O2 codes. Typically with replaced headers, yes. But also those without. But keep in mind, no cats will kill them especially fast by comparison.
If you decide to change your sensors out, make sure they are OEM straight from Ford (not Bosh etc.) Tuning has shown us that the aftermarket sensors heat up and cool down just differently enough than OEM to possibly throw codes.
|
see link above,
OEM parts have their fair share of problems too, as ive never seen a car with 7k miles(my own)throw an 02 so early with simlpe bolt ons. Given the conditions of my situation i understand the cause, but upon purchase of another OEM replacement 02, it was faulty.
From this experience ive began to think its not the absence of cats causing the problem, but the placement of the 02's with LT's being further downstream. My issue was post cat so regardless of if cats were installed, i doubt it would have changed the issue.
Some food for thought for those of you lowered with longtubes, How close is your front 02 bungs to the ground? Connector placement?
Now compare to stock placement and connections. May be a reason for that?
Also i wanted to mention, my 11 SG car had an O/R pipe and stock headers tune and bolted @ 800 miles, never had one issue with the front 02's in 20K miles.
|
|
|
10-11-2012, 11:27 AM
|
#7
|
DFW5.0s Preferred Vendor
Join Date: Aug 2012
Location: McKinney
Posts: 676
|
Originally Posted by Courtesy Flush
Funny you ask, http://dfw50s.com/showthread.php?t=454
been a nightmare and $300 to get this mess fixed.
see link above,
OEM parts have their fair share of problems too, as ive never seen a car with 7k miles(my own)throw an 02 so early with simlpe bolt ons. Given the conditions of my situation i understand the cause, but upon purchase of another OEM replacement 02, it was faulty.
From this experience ive began to think its not the absence of cats causing the problem, but the placement of the 02's with LT's being further downstream. My issue was post cat so regardless of if cats were installed, i doubt it would have changed the issue.
Some food for thought for those of you lowered with longtubes, How close is your front 02 bungs to the ground? Connector placement?
Now compare to stock placement and connections. May be a reason for that?
Also i wanted to mention, my 11 SG car had an O/R pipe and stock headers tune and bolted @ 800 miles, never had one issue with the front 02's in 20K miles.
|
I actually talked with my Ford guy this morning to get an O2 shipped. I asked if anything "funny" had been going on with O2's that he knew of. He said no. But then, for the first time, his system asked if the build date was (i think April 2010) or beyond. He said this was new. Perhaps something is developing and we just don't know what....yet.
From this experience ive began to think its not the absence of cats causing the problem, but the placement of the 02's with LT's being further downstream.
|
Placement is a factor.
Also i wanted to mention, my 11 SG car had an O/R pipe and stock headers tune and bolted @ 800 miles, never had one issue with the front 02's in 20K miles.
|
Same or different brand?
*Sorry...can't delete my double post.
Last edited by TrueStreetTim; 10-11-2012 at 11:31 AM.
|
|
|
10-11-2012, 12:16 PM
|
#8
|
Senior Member
Join Date: Aug 2012
Location: Keller, TX
Posts: 613
|
Originally Posted by TrueStreetTim
I actually talked with my Ford guy this morning to get an O2 shipped. I asked if anything "funny" had been going on with O2's that he knew of. He said no. But then, for the first time, his system asked if the build date was (i think April 2010) or beyond. He said this was new. Perhaps something is developing and we just don't know what....yet.
|
Upon ordering i was told there was two 02 part #'s available under my vin #. Both specified as front 02's left and right. One was $120 other was close to $200.
Ill agree, something has developed.
I bought the $120 one it never worked. Took it to shop and they bought another $120 one and it worked. hmm
Originally Posted by TrueStreetTim
Same or different brand?
|
Lethal O/R X on the 11 car
SW LT's and o/r X on the 12.
|
|
|
10-11-2012, 01:47 AM
|
#9
|
My Stapler!
Join Date: Jun 2012
Location: Dtown
Posts: 1,928
|
I have longtube.
__________________
2012 GT/CS
93 Cobra
|
|
|
10-11-2012, 10:18 AM
|
#10
|
Scared to race Steve
Join Date: Jun 2012
Location: Hiding from Steve
Age: 42
Posts: 2,646
|
Originally Posted by Phuck Phace
I have longtube.
|
In your ass
__________________
Originally Posted by SlowGreyGT
I agree. A stick car shocks the tires MUCH harder and does it several times going down the track. With a big power stick car, the car is much more unsettled going down the track making it more of a challenge to ET well. A well running auto car is nothing more than just point and shoot. Which is great for a track car taking a lot of driver error out of the equation.
|
|
|
|
10-22-2012, 06:19 PM
|
#11
|
Senior Member
Join Date: Oct 2012
Location: Mustang, Ok
Posts: 259
|
the paxton tune was extremely rich though. If im not mistaken I think our cats might be the same as the 11-12 GT500s
__________________
2015 Comp Orange GT Premium Perfomance Pack
SOLD!
2012 Kona Blue GT Premium
Roush TVS/JLT Big Air
Stainless Works Long Tubes and catted X.
Magnaflow Competition Catback
AED Tuned
***Driver Mod***
10.88@134 on street tires
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|