Go Back   Dallas Fort Worth 5.0 Mustang Club > 5.0 Mustang Forum > Interior/Exterior

Interior/Exterior Post new mods or questions about the inside or outside of your mustang


Sponsored Ads
Welcome to DFW50s.com

Register to remove these ads.




Reply
 
Thread Tools Display Modes
Old 06-03-2014, 09:58 AM   #1
2012mustang76123
Senior Member
 
Join Date: Jul 2013
Age: 35
Posts: 116
Default So has anyone actually did a diy headlight retrofit?

Want to try it out when I get a spare headlight in. I know you can have them shipped off and done for 600-700 but I want to do a diy since a halogen stock headlight can be gotten for 40-60.

I know you have to dremel the headlight. Just wondering if anyone has done it and can give pointers or if they created an install guide of some sort.
2012mustang76123 is offline   Reply With Quote
Old 06-03-2014, 11:14 AM   #2
Pewter Lurch
Senior Member
 
Join Date: Oct 2012
Location: Rowlett, TX
Age: 32
Posts: 163
Default

I sent mine out. A lot easier. If you get on the dfw5.0 facebook page frank did his own.
__________________


2011 Mustang GT Premium
The Go Fast:
Magnaflow 3" OA | Pypes X-Pipe | Steeda CAI | VMP Tune | BBK Cat Deletes | SVT GT500 quad mufflers |

The Ride & Look Good:
Ford K Springs | BMR Adj. LCAs | BMR Relo. Brackets | BMR Adj. PHB | GT500 Spoiler | Boss Rear | Retrofit Headlights | GT/CS facia | Boss splitter | Retro billet grille | Steeda X Brace | Enkie RPF1 18x8/18x9.5 | '14 tail lights | '14 GT500 quad bumber |

Collecting Dust:
|Go Fast Parts(SHHHH no one knows)|
Pewter Lurch is offline   Reply With Quote
Old 06-03-2014, 11:45 AM   #3
DirtyD
Senior Member
 
Join Date: Jun 2012
Posts: 5,594
Default So has anyone actually did a diy headlight retrofit?

I thought Frank bought his already retrofitted?

It's actually not a hard process, just tedious to make sure everything is lines up correctly and square.

I started a set on my old truck, but didn't get to finish them before the truck was totaled. The killer in the price of having them done for you is the labor charges. Materials can be had for a good price through The Retrofit Source
DirtyD is offline   Reply With Quote
Old 06-03-2014, 12:02 PM   #4
2012mustang76123
Senior Member
 
Join Date: Jul 2013
Age: 35
Posts: 116
Default

Dont have a spare car that can manage to get into the job that I work at ( other too low) so I have to use the mustang as a main vehicle so can't send off headlights.

So based on that site you sent yours out at my total would come to 820 before any shipping charges etc.

Headlights - 100/ 100 if I bought my own.
projector - Included or 150 extra for fxr/ mini- 100 fxr 3.0-70 ( dont know if they are the 3.0 or the original ones couldn't find any on site to confirm.
Shroud- Included/ 45
Paint- gloss black 70/ 50 to send it off and have it painted with custom paint on shrouds.
Hid- Included (dont know what brand)/ 55 off brand/ 85 morimoto
Time- included/ Say 5 hrs
Cost- 820 vs 340

They might turn out worse or better but I figure it'll be worth the chance to try them out
Plus I want to do something like this on a mustang though.
2012mustang76123 is offline   Reply With Quote
Old 06-03-2014, 01:28 PM   #5
DirtyD
Senior Member
 
Join Date: Jun 2012
Posts: 5,594
Default

You can find a decent pair of factory headlights that some ditched for Raxioms for a good price typically.

If you are going to do it yourself, I recommend doing an OE ballast and bulb setup, like the Denso + Osram bulbs.

As for the projector, the Mini has become quite popular. I think the FX-R in a 2.5" might be big, but you would have to see what other people are using in S197 housings.

I recommend that you get with the shop that did Grant's, or get with Yuke's Retrofits (on Facebook of SVTPerformance) as he does a number of S197 lights and can tell you the best overall fit, as well as give a few pointers.
DirtyD is offline   Reply With Quote
Old 06-03-2014, 03:48 PM   #6
Pewter Lurch
Senior Member
 
Join Date: Oct 2012
Location: Rowlett, TX
Age: 32
Posts: 163
Default

I have a pair of factorys sitting in my garage! And mine cost me $650. With new housing.
__________________


2011 Mustang GT Premium
The Go Fast:
Magnaflow 3" OA | Pypes X-Pipe | Steeda CAI | VMP Tune | BBK Cat Deletes | SVT GT500 quad mufflers |

The Ride & Look Good:
Ford K Springs | BMR Adj. LCAs | BMR Relo. Brackets | BMR Adj. PHB | GT500 Spoiler | Boss Rear | Retrofit Headlights | GT/CS facia | Boss splitter | Retro billet grille | Steeda X Brace | Enkie RPF1 18x8/18x9.5 | '14 tail lights | '14 GT500 quad bumber |

Collecting Dust:
|Go Fast Parts(SHHHH no one knows)|
Pewter Lurch is offline   Reply With Quote
Old 06-03-2014, 03:51 PM   #7
Pewter Lurch
Senior Member
 
Join Date: Oct 2012
Location: Rowlett, TX
Age: 32
Posts: 163
Default

That includes everything and the 3 stage automotive black gloss paint, shrouds, hids, projectors and everything
__________________


2011 Mustang GT Premium
The Go Fast:
Magnaflow 3" OA | Pypes X-Pipe | Steeda CAI | VMP Tune | BBK Cat Deletes | SVT GT500 quad mufflers |

The Ride & Look Good:
Ford K Springs | BMR Adj. LCAs | BMR Relo. Brackets | BMR Adj. PHB | GT500 Spoiler | Boss Rear | Retrofit Headlights | GT/CS facia | Boss splitter | Retro billet grille | Steeda X Brace | Enkie RPF1 18x8/18x9.5 | '14 tail lights | '14 GT500 quad bumber |

Collecting Dust:
|Go Fast Parts(SHHHH no one knows)|
Pewter Lurch is offline   Reply With Quote
Old 06-06-2014, 04:20 PM   #8
2012mustang76123
Senior Member
 
Join Date: Jul 2013
Age: 35
Posts: 116
Default

Did you have to splice the wires in or were they plug and play?
2012mustang76123 is offline   Reply With Quote
Old 06-06-2014, 09:23 PM   #9
DirtyD
Senior Member
 
Join Date: Jun 2012
Posts: 5,594
Default

Originally Posted by 2012mustang76123 View Post
Did you have to splice the wires in or were they plug and play?

Plug and play. A harness will be used which has pigtails for a 9006 where the other end plugged for the HIDs
DirtyD is offline   Reply With Quote
Old 06-09-2014, 01:02 PM   #10
2012mustang76123
Senior Member
 
Join Date: Jul 2013
Age: 35
Posts: 116
Default

Originally Posted by DirtyD View Post
Plug and play. A harness will be used which has pigtails for a 9006 where the other end plugged for the HIDs
Where would you get a harness like that to work with our connector? Want to use d2s bulbs if i do diy
2012mustang76123 is offline   Reply With Quote
Old 06-09-2014, 01:05 PM   #11
Pewter Lurch
Senior Member
 
Join Date: Oct 2012
Location: Rowlett, TX
Age: 32
Posts: 163
Default

I HIGHLY recommend ordering morimoto hid kit. Yes it is expensive but it will come with everything you need and they will last. Trust me!
__________________


2011 Mustang GT Premium
The Go Fast:
Magnaflow 3" OA | Pypes X-Pipe | Steeda CAI | VMP Tune | BBK Cat Deletes | SVT GT500 quad mufflers |

The Ride & Look Good:
Ford K Springs | BMR Adj. LCAs | BMR Relo. Brackets | BMR Adj. PHB | GT500 Spoiler | Boss Rear | Retrofit Headlights | GT/CS facia | Boss splitter | Retro billet grille | Steeda X Brace | Enkie RPF1 18x8/18x9.5 | '14 tail lights | '14 GT500 quad bumber |

Collecting Dust:
|Go Fast Parts(SHHHH no one knows)|
Pewter Lurch is offline   Reply With Quote
Old 06-09-2014, 01:53 PM   #12
DirtyD
Senior Member
 
Join Date: Jun 2012
Posts: 5,594
Default

Originally Posted by 2012mustang76123 View Post
Where would you get a harness like that to work with our connector? Want to use d2s bulbs if i do diy
The retrofit source will include that harness when you purchase a kit from them. A third party retrofitter/installer should also include it as well.
DirtyD is offline   Reply With Quote
Reply

Bookmarks




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump