Go Back   Dallas Fort Worth 5.0 Mustang Club > 5.0 Mustang Forum > General Discussions

General Discussions Discuss anything in general about your 5.0 Mustang that doesn't belong within the other categories here.


Sponsored Ads
Welcome to DFW50s.com

Register to remove these ads.




Reply
 
Thread Tools Display Modes
Old 12-07-2012, 02:14 AM   #1
blownaltered
I have a small penis
 
Join Date: Nov 2012
Location: Making Steve my bitch since 2003
Age: 44
Posts: 1,465
Default Oil leak

I guess i should start by saying this is an 89 gt with a 302. I have oil on the top of my block on the back side of my motor behind intake. It goes around the sides below the heads also. The only thing I can come up with is the rear main but I wouldn't think it would get oil up there so could it be from the heads. I know the oil pan gaskets leaks and that will be fixed this week but I just can't seem to figure out where the oil on top of the motor is coming from.
blownaltered is offline   Reply With Quote
Old 12-07-2012, 02:19 AM   #2
Grandpa
I> /\/\
 
Grandpa's Avatar
 
Join Date: Jun 2012
Location: A fender ahead of BlownAltered
Posts: 7,562
Default

EGR still on the car?
Grandpa is offline   Reply With Quote
Old 12-07-2012, 02:25 AM   #3
blownaltered
I have a small penis
 
Join Date: Nov 2012
Location: Making Steve my bitch since 2003
Age: 44
Posts: 1,465
Default

Yes
blownaltered is offline   Reply With Quote
Old 12-07-2012, 02:28 AM   #4
blownaltered
I have a small penis
 
Join Date: Nov 2012
Location: Making Steve my bitch since 2003
Age: 44
Posts: 1,465
Default

No oil around it
blownaltered is offline   Reply With Quote
Old 12-07-2012, 03:10 AM   #5
STROKD
Old School
 
Join Date: Oct 2012
Age: 46
Posts: 1,358
Default

Valve Cover gaskets

Edit, or PCV valve isnt in place, or gasket fell out... check the PCV system and your valve covers... if you have the old cork ones, throw them away and buy the later model metal and rubber gaskets. Those dont leak.
__________________
86 GT 374 Billet "W" w/ 72MMs
90 GT 351 Dart short stroke w/ YSi
STROKD is offline   Reply With Quote
Old 12-07-2012, 11:12 AM   #6
blownaltered
I have a small penis
 
Join Date: Nov 2012
Location: Making Steve my bitch since 2003
Age: 44
Posts: 1,465
Default

[QUOTE=STROKD;11501]Valve Cover gaskets

Edit, or PCV valve isnt in place, or gasket fell out... check the PCV system and your valve covers... if you have the old cork ones, throw them away and buy the later model metal and rubber gaskets. Those dont leak.[/

The valve cover gasket on the passenger side is leaking but not in the back. The driver side is not leaking at all. I believe Sean at truestreetmotorsports checked the Pcv valve before dynoing the car a few weeks ago but I will check it again.
blownaltered is offline   Reply With Quote
Old 12-07-2012, 11:35 AM   #7
blownaltered
I have a small penis
 
Join Date: Nov 2012
Location: Making Steve my bitch since 2003
Age: 44
Posts: 1,465
Default

Pcv valve is in but does look like it is leaking around it. Could have bad o-ring. I will pick up valve cover gaskets and new Pcv vale today to install this weekend. There is oil all over the top of the bell housing of the tranny. Not sure if these are the cause but I guess it's a start
blownaltered is offline   Reply With Quote
Old 12-07-2012, 05:41 PM   #8
STROKD
Old School
 
Join Date: Oct 2012
Age: 46
Posts: 1,358
Default

I assume you have a valve cover breather? If not the pcv could just blow out under boost. Lol
__________________
86 GT 374 Billet "W" w/ 72MMs
90 GT 351 Dart short stroke w/ YSi
STROKD is offline   Reply With Quote
Old 12-07-2012, 06:33 PM   #9
blownaltered
I have a small penis
 
Join Date: Nov 2012
Location: Making Steve my bitch since 2003
Age: 44
Posts: 1,465
Default

Originally Posted by STROKD View Post
I assume you have a valve cover breather? If not the pcv could just blow out under boost. Lol
It has a breather but that leaks a little. It doesn't have the baffle, looking for valve covers that will work with a baffle.
blownaltered is offline   Reply With Quote
Old 12-07-2012, 09:47 PM   #10
Toby
Senior Member
 
Join Date: Aug 2012
Age: 37
Posts: 459
Default

the rear portion of the intake could not be sealed good.
Toby is offline   Reply With Quote
Old 12-07-2012, 10:42 PM   #11
blownaltered
I have a small penis
 
Join Date: Nov 2012
Location: Making Steve my bitch since 2003
Age: 44
Posts: 1,465
Default

Originally Posted by Toby View Post
the rear portion of the intake could not be sealed good.
My dad and I were talking about that this evening. I guess the only real way to check that would be to pull the intake. Shit I guess it's something else to add to the list of shit to do. If I have to do that I might as well put the bigger injectors the motor needs, no sense in pulling the upper intake twice
blownaltered is offline   Reply With Quote
Old 12-15-2012, 12:06 PM   #12
blownaltered
I have a small penis
 
Join Date: Nov 2012
Location: Making Steve my bitch since 2003
Age: 44
Posts: 1,465
Default

Well took the car to a buddy of mine and she is all fixed up. The oil pan gasket and the Pcv valve were the problems. The Pcv valve was toast, the rubber deal was bad and there was no oil screen, that was leaking pretty bad. All other seals look good. Have one little leak because of the valve cover breather but I will need new valve covers to fix. But I fixed my hood so now I have the clearance to do it. Now I don't have to replace my hood, lots of money saved right there.
blownaltered is offline   Reply With Quote
Reply

Bookmarks




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump