![]() |
Tranny Bushing Review
Got mine the other day and did the install in about 10-15 mins. The part that took me the longest was getting the car in the air.
My review of the part: * Definitely stiffened the tyranny up, some noticeable extra vibrations coming through the floor boards but nothing excessive. * Definite improvement in shift responsiveness. * Overall it feels solid and more fun to drive. I highly recommend this part. Also I am completely stock as far as the shifter goes and to be honest right now I think i'll keep it that way. I've done a few high rpms shifts and it feels good no lock-out. Thank again Vorshlag, a great product indeed! |
how much was it?
|
Quote:
Including tax and shipping in Texas it runs right under $40. You can also pick one up in person at the shop. Bonus, you get to meet Terry! http://vorshlag.smugmug.com/Product-...5%20copy-M.jpg |
Picked mine up at the shop today. It will be going in this weekend with my other parts
|
I stopped by on Friday to get one. Terry wasn't there, he was working out at the gym while his crew were at the shop busting ass. The V8 Miata is going to be badass and the Chump C4 is going to be DQ'd!
The bushing works as advertised, but the vibrations in the floorboard at ~2500rpm are gnarly. I've driven solid engine mount cars for years and they don't make the chassis groan like this thing does. I'll probably pull it out for daily duty, it's a bit much for that. But it's cheap, very effective, and since it takes about 5 minutes to install it I'll just toss it in when I know I'll be working it hard. Great mod, especially for the price. |
Quote:
|
Quote:
|
Good review. Thanks for the info Danny
|
Quote:
Quote:
1. Installing the bushing insert backwards. We've seen it done, and it takes talent, but if you follow the included instructions you can't screw it up. It will go in from the wrong direction but you have to force it in and it doesn't fit right. To install this kit correctly you have to DROP the transmission crossmember, and we think some folks are trying to short cut this step and shove it in from the wrong side. http://vorshlag.smugmug.com/Product-..._DSC1571-L.jpg 1. A. Some folks cut the center tip off of the insert to reduce vibrations, but we haven't needed to do this yet. and that piece is a big chunk of the bushing insert. 2. Other parts in the driveline that are already amplifying the NVH. Aluminum 1-piece driveshafts might be a culprit, but I suspect it is aftermarket shifters. Many people use aftermarket short shift kits, which generally replace the body mounted shift bushing (with poly or metal), remove a bushing in the shift arm (going to a solid shaft), and some other parts are made metal - to the point that MOST shifters already add some buzz. Maybe this WL bushing kit added to a few brands of shifters causing "too much?? Don't know, because of the dozen or so we've installed on '11-14 Mustangs, many of which had shifters, we have yet to see one buzz. ??? http://vorshlag.smugmug.com/Racing-E..._DSC9511-L.jpg All I know is that I noticed a tiny bit of added NVH but felt a LOT more connected to the shifter when rowing the gears. Recently we installed some aftermarket "Race" poly motor mounts, too. No massive NVH increase, to me. I drove the car around town recently, and it is generally pretty quiet under 4000 rpms, I could barely detect a vibration. In a typical race weekend I might make a few hundred shifts and I've had no missed gears or issues since adding the Whiteline KDT928 kit + a Steeda rear shift bushing (95A poly), and recently race poly motor mounts. But I still use the stock shifter, and gladly. http://vorshlag.smugmug.com/Projects..._DSC9107-L.jpg Your Results May Vary. |
So which direction is backwards?
Instruction show to insert the bushing from the front of the cross member (facing the back of the vehicle). I can't insert it the other direction because of my Stiffler's DS loop. |
Y'all have these in stock now, right?
|
Quote:
Quote:
|
Quote:
Well if y'all still have some in a couple of weeks when i'm in town i'll stop by. |
Installed mine from the front. I took the crossmember and trans mount out, then used lube and a vise to make sure the bushing was seated all the way. I verified it wasn't touching the crossmember before installing back in the car. I'm pretty particular about suspension and drivetrain parts being installed correctly.
I'm also a wuss, so it's been too cold for me to get back under it and see what's up. I might trim the whole center piece out like some have to see if that makes a difference. If it does, I'll report back. In the meantime, banging gears like a madman has been fun. PS - I have some generic poly bushing "shifter bracket" in the car. Otherwise the drivetrain is 100% stock. |
1 Attachment(s)
Figgered it out.
Took down the trans mount and it was immediately apparent that the lower/wider section of the WL bushing was protruding through far enough to make contact with the crossmember. It was obvious where it was rubbing. So I grabbed a razor blade and trimmed off the part that protrudes through the trans mount, about 3/8", all the way across. Some people whack off that whole lower section of the bushing, but that seems drastic. Took it for a spin and NVH-wise I can't even tell anything is different than stock, but high rpm shifts are precise as before. This is how it's supposed to feel. Pic of the remnant below. |
All times are GMT -4. The time now is 08:12 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.